Crane Pumps & Systems — Burks Brand · Piqua, Ohio · Est. 1856

Model 131077 · Close Coupled End Suctions · Burks

1.5″ – 3″ DischargeUp to 1,100 gpmUp to 380 ft Head1 – 75 HP Range

The Burks 131077 burks 131077 – ga series pump, frame 15, model 4-1, 4.25" trim. Burks offers a broad line of centrifugal pumps in close-coupled or base-mounted configurations. These pumps are designed for general purpose pumping, circulation, liquid transfer or booster service. Burks pumps are built for long life and all are factory teste Series capacity up to 1,100 gpm at 380 ft head.

HP Range

1 – 75

Max Flow

1,100 gpm

Max Head

380 ft

Discharge

1.5″ – 3″

Speed

1750, 3450

Crane Pumps Engineering

Burks — manufactured by Crane Pumps & Systems, Piqua, Ohio since 1856

Crane Pumps & Systems

A Crane Co. company — 165+ years of pump engineering. Burks, Burks, Deming, and Weinman under one roof in Piqua, Ohio

Wide HP Range

1 – 75 HP available

Expert Support

Technical sizing and compatibility help — call (781) 281-8905 or chat

Why This Product

Close-Coupled End-Suction Design — Compact and Serviceable

Close-coupled design eliminates the flexible coupling and separate bearing housing of frame-mounted pumps — fewer components, smaller footprint, and lower maintenance requirements.

Back Pull-Out — Service Without Disturbing Piping

ANSI-frame back pull-out design allows impeller, seal, and wear ring service without disconnecting suction or discharge piping — reducing service time and cost on permanently installed pumps.

Multiple Construction Options

Bronze fitted, all-bronze, all-iron, and specialty material configurations. Seal material options cover water, wastewater, chemical, and petroleum service. Flanged casing available for code-compliant installations.

NEMA-Frame Motor — Standard Interchangeability

Standard NEMA motor frame allows direct field motor replacement with any major manufacturer's motor — no custom parts or factory service when only the motor has failed.

Wide HP Range — One Series for Multiple Duties

All models in the series share casing dimensions and spare parts — changing HP requires only a motor swap, not repiping or a new pump casing.

Deming · Weinman · Burks — Crane Pumps Engineering

Deming, Weinman, and Burks end-suction pumps are manufactured by Crane Pumps & Systems in Piqua, Ohio — trusted in HVAC, industrial, and municipal applications for over a century.

Technical Specifications

Model Number	131077
Series	Close Coupled End Suctions
Brand	Burks
Horsepower	1 – 75
Series HP Range	1 – 75
Max Flow Rate	1,100 gpm
Max Head	380 ft
Discharge Size	1.5″ – 3″
Speed	1750, 3450

Key Features

Four position casing allows discharge to be oriented in any of the four positions

Enclosed bronze impeller threads onto stainless steel shaft

Enclosed glass filled boryl impeller to maximize efficiency

Suitable for temperatures up to 500°F

Available Options

Bronze Fitted, All Bronze or All Iron Construction

Mechanical Seal upgrade

Flanged Casing

Shaft Sleeve Material

Explosion Proof

Typical Applications

HVAC

Commercial

Important Notices

Fluid compatibility	For use with liquids compatible with pump component materials. Verify chemical, temperature, and pressure compatibility before use.
Electrical	Requires a properly sized grounded branch circuit and motor starter with correctly rated thermal overload protection.
Operating limits	Do not exceed series pressure, temperature, and speed ratings. Operation outside rated limits causes premature seal and bearing failure.
Service	Disconnect and lockout/tagout power before any service. Allow pump to cool before handling after operation.

Available Documentation

✓ Product Specification Sheet — Close Coupled End Suctions

✓ Installation, Operation & Maintenance Manual (IOM)

✓ Repair Parts Manual

✓ Product Catalog — Product Catalogs

Need the spec sheet, IOM, or parts list? Contact PumpStop and we'll send it over.

Before You OrderConfirm HP, voltage, phase, and enclosure type are correct for your installation. All models in the Close Coupled End Suctions share casing dimensions and spare parts — motor configuration is the only difference between models. For sizing guidance, chat or call (781) 281-8905.

Burks 131077 – GA Series Pump, Frame 15, Model 4-1, 4.25" Trim

Description

Close-Coupled End-Suction Design — Compact and Serviceable

Back Pull-Out — Service Without Disturbing Piping

Multiple Construction Options

NEMA-Frame Motor — Standard Interchangeability

Wide HP Range — One Series for Multiple Duties

Deming · Weinman · Burks — Crane Pumps Engineering

Quote for 45220C0

Quote for 45480B0

Quote for 4508000

Quote for 23310AG

Quote for 8105000

Quote for 240600B

Quote for 206500B

Quote for 206500G

Quote for 240100G

Quote for 206500B

Quote for 2421200

Quote for 206500G

Quote for 2454000

Quote for 206500B

Quote for 2425200

Quote for 8082000

Quote for 8157000

Quote for 53250J0

Quote for 2421200

Quote for 8157000

Quote for 5045000

Quote for 2452000

Quote for 4405000

Quote for 4918000

Quote for 206500B

Quote for 8105000

Quote for 703/LEH102A

Quote for 702/LE72A

Quote for 702/LE102A

Quote for EV290HV-5BL

Quote for EV290-5BL

Quote for EV280HV-5BL

Quote for 45220C0

Quote for 45480B0

Quote for 4508000

Quote for 4405000

Quote for 8157000

Quote for 2454000

Quote for 1007-999-B0

Quote for 1434-006-90

Quote for 1560-000-02

Quote for 1557-000-00

Quote for 100547A

Quote for 100547B

Quote for 100547A

Quote for 100547B

Quote for 9-850835-04

Quote for 9-100834-04

Quote for 9-100835-04

Quote for 108344HF

Quote for 110981-KIT

Quote for 116429

Quote for 233HV

Quote for LNV100

Quote for LNV75

Quote for 4351000

Quote for K001314

Quote for K002080

Quote for 1007-999-B0

Quote for 1434-006-90

Quote for 1560-000-02

Quote for 96717383

Quote for 96717435

Quote for 91836569

Quote for 98562817

Quote for 96901187

Quote for 853344-X3

Quote for EV290HV-5BL

Quote for EV280HV-5BL

Quote for EV290-5BL

Quote for EV290HV-5BL

Quote for EV290-5BL